V9: Strike-Legal

From AmtWiki
(Redirected from V9: Heavy Padding)
221202---V9-Rules-Seal-for-Wiki.png
This page is part of the Official Amtgard V9 Alpha-Playtest Rulebook.
  • The Amtwiki is the official home and primary source for Amtgard V9 Rules as of February 25, 2023.
  • These rules are currently in Open Alpha Playtest. See the Playtest Disclaimer for more details.
  • To learn more about Amtgard V9 Development, please visit Amtgard.com.
  • To view the current Amtgard V8 ruleset, please see the Amtgard V8 Rulebook.




Strike-Legal Padding

An Omni weapon is Strike-Legal around the entire circumference.

Strike-Legal Padding is padding that is used to create striking surfaces that are safe to strike another player with.

  1. Weapons that require Strike-Legal Padding must be sufficiently padded to prevent injury if used to strike an opponent with the most force that could reasonably be expected in Amtgard combat. Combat contact with the strike-legal portions of a weapon must not be unreasonably painful, nor should it leave bruises or have the potential to break bones and teeth when used by an average player as well as its intended user.
    • Regardless of the requirements listed below, Hit Testing will always be required to assess the more subjective aspects of Strike-Legal padding, such as impact force and player comfort.
    • Since combat is chaotic and every participant has different pain tolerances and sensitive areas, occasional instances of uncomfortable contact should be expected, however repeated or egregious offenses from the same weapon should result in the weapon and/or the user being removed from play.
  2. No part of the weapon’s striking surface, whether the tip, the edge, the face or any other part, may protrude more than 1.5" through a two-and-a-half inch (2.5") ring when uncompressed.
  3. All Strike-Legal surfaces must have an opaque cover and be visually distinct from Non-Striking Surfaces on the same weapon.
Melee Strike Legal
An Flatblade weapon is Strike-Legal on only one or two edges.

In addition to the above, Strike-Legal padding on melee weapons must follow these additional rules:

  1. Strike-Legal Padding must begin at each Striking Tip and move inward along the core toward the handle. It must be continuous for the entire required length. Any forked segments that split from a Strike-Legal point must also be entirely Strike-Legal.
  2. Must have at least 1" of safety-grade foam over the weapon core.
  3. Must have a continuous cross-section of at least 2.5" from edge to edge.
  4. The entire circumference of the core does not need to be strike-legal, however any part of this circumference that is not strike-legal must be covered with Incidental Padding and cannot be used to strike.
  5. Striking Tips must be sufficiently capped to resist stab impact and prevent the core from pushing through. The foam should not deflect or fold over excessively when stabbing and always return to its original position.
    • It is strongly recommended that weapons intended to regularly strike with a thrusting motion also include comfort-grade foam on the tip to further cushion the blow. Weapons designed for two-handed stabs, such as large pikes, may need even more padding than smaller, single-handed weapons. Hit Testing will help determine what is the ideal amount of extra padding for player safety and comfort.

Heavy Padding
From left to right: Regular Padding, Heavy Padding, Super Heavy Padding

A segment of a melee weapon is considered to have Heavy Padding if it meets the requirements for Strike-Legal padding and also has an edge-to-edge, cross-section of 4" or greater (instead of 2.5"). This extra padding must begin within 3" of the Striking Tip and proceed continuously towards the handle.

  • Heavy Padding can apply to flat-blade weapons. The 4" cross-section does not need to be around the entire core.

Heavy Padding Substitution
For each inch of Heavy Padding added along the core, you may replace one (1) inch of required Strike-Legal Padding with Incidental Padding.

  • Incidental Padding added in this manner must begin by replacing the padding closest to the handle and then proceed continuously towards the Striking Tip.
  • A weapon cannot substitute more than 50% of its required Strike-Legal padding this way.
Super Heavy Padding

Super Heavy Padding follows the same rules as Heavy Padding except it requires a cross-section of 8" or greater. If both Heavy and Super Heavy padding are used together, the Super Heavy Padding must be closest to the tip.

Super Heavy Padding Substitution
This follows the same rules as Heavy Padding Substitution except for each inch of Super Heavy Padding added along the core, you may replace two (2) inches of required Strike-Legal Padding with Incidental Padding.

Example: A 48" Long weapon would typically require 32" of Strike-Legal padding. Using Heavy Padding Substitution you could have 16" of Heavy Padding, followed by 16" of Incidental Padding; and with Super Heavy Padding Substitution, you could have 8" of Super Heavy padding, followed by 8" of regular Strike-Legal, and then 16" of Incidental Padding.





Weapon Construction Terms
2.5 Inch and 2 Inch Rule · Core · Covers · Flex · Handle / Unpadded · Incidental Padding · Multi-Ended Weapons · Non-Striking Tip · Ownership Label · Padding & Foam · Stab-Only · Strike-Legal · Striking Tip · Total Length · Weapon Segments
Weapons
General Rules · Weapon Construction Terms · Melee Weapons · Projectile Weapons · Siege Weapons
Equipment
Equipment Basics · Equipment Use Terms · Weapons · Shields · Armor · Color Code · Visual Indicators
Amtgard V9 Rulebook
Playtest Disclaimer · Introduction · Getting Started · Garb · Honor System · Safety · Core Combat Rules · Equipment · Classes · Abilities and Effects · Magic Items · Combat Activities · Rules Authorities
Appendix: Equipment Inspection Guide · Master List of Abilities · Glossary