V9: Armor Rating Modifiers

This page is part of the Official Amtgard V9 Alpha-Playtest Rulebook.

• The Amtwiki is the official home and primary source for Amtgard V9 Rules as of February 25, 2023.
• These rules are currently in Open Alpha Playtest. See the Playtest Disclaimer for more details.
• To learn more about Amtgard V9 Development, please visit Amtgard.com.
• To view the current Amtgard V8 ruleset, please see the Amtgard V8 Rulebook.

---

Armor Modifiers

Armor pieces can be granted bonuses or penalties to their Armor Rating based on the quality of construction or appearance. Multiple points can be awarded and penalized simultaneously as long as they each correspond to each unique feature or collection of features that would warrant the bonus or penalty if viewed on its own.

Superior Appearance
Bonus points may be awarded to armor that displays an exceptional appearance above and beyond the typical appearance of similar pieces in its style. This includes but is not limited to: tooling, etching, gilding, and fluting, as well as notable use of colors, shapes, weaves, etc. These examples do not represent an exhaustive list and consideration should be given to any piece that obviously goes above and beyond the base construction requirements to create an aesthetically pleasing piece.

Inferior Appearance
Points may be deducted from armor that displays an appearance well below the typical standard expected for similar pieces in that style. Examples include tarnished/poorly-maintained armor as well as visibly inauthentic or degraded materials. This penalty does not apply when the piece is worn as a part of a complete outfit that is intentionally designed to look shoddy or battle-worn.

Superior Construction
Bonus points may be awarded to armor constructed with exceptional techniques that provide a meaningful increase in durability over the standard for the material being used. This includes but is not limited to: solid/riveted rings, hardened material, noticeably tighter spacing than required, etc. This bonus may also be granted to pieces that are at least 75% steel or equivalent metal. These examples do not represent an exhaustive list and consideration should be given to any piece that obviously goes above and beyond the base requirements to create a more durable piece.

Inferior Construction
Points may be deducted from armor for inferior construction techniques or a meaningful reduction in expected durability when compared to the standard for the material being used. Examples include but are not limited to: obviously unfinished armor, brittle/cracked material, loose connection points, and shoddy workmanship.

Layered Armor Bonus
If multiple unique pieces of Physical Armor are layered on top of each other as part of a complete outfit, the rating of any overlapping area will be rating of the highest-tier armor piece plus 1, up to that armor’s maximum.

1. A piece of armor already at max rating will not receive any additional value from layering.
2. Each layered piece should be able to act as armor on its own if it were not layered. The layers may be affixed while being worn, such as metal armor attached to an arming doublet.
3. Any part of layered armor that extends beyond the layering is calculated at its normal rating.
4. All layered armor pieces must be at least partially visible in a way that does not misrepresent the wearer’s armor point total or armor coverage when observed by another player from 20ft away. This especially true in the cases where a lower-tier armor is layered on top of a higher-tier piece.
5. There is no additional bonus for layering more than two pieces.

Material Thickness

Certain armor styles may require materials that meet a specific thickness. Multiple layers of material may permanently affixed to each other to increase thickness however extra thickness caused by adhesives or empty space should not be factored into the new measurements.

• One bonus point may be awarded or deducted for Superior or Inferior thickness according to the chart below.
• Armor pieces that do not meet these minimum requirements may be judged as Ambiguous Armor as long as they still meet the universal equipment requirements.

MATERIAL THICKNESS REFERENCE CHART
	Inferior (Minimum)		Standard		Superior		Notes
Cloth	Cannot be less than standard		1/16" 1.60mm		1/8" 3.18mm
Light Leather	4oz 1/16" 1.60mm		6oz 3/32" 2.39mm		8oz 1/8" 3.18mm
Heavy Leather	Cannot be less than standard		10oz 5/32" 3.96mm		12oz 3/16" 4.78mm		Less than standard is Light Leather
Rigid, Non-Metal	1/8" 3.18mm		3/16" 4.78mm		1/4" 6.36mm		Material Density at least 0.9g/cm3 (equivalent to HDPE)
	Aluminum	Steel	Aluminum	Steel	Aluminum	Steel
Round Rings	18ga swg 16ga awg 0.048" 1.219mm	20ga swg 18ga awg 0.036" 0.914mm	16ga swg 14ga awg 0.064" 1.626mm	18ga swg 16ga awg 0.048" 1.219mm	14ga swg 12ga awg 0.080" 2.032mm	16ga swg 14ga awg 0.064" 1.626mm
Flat Rings	20ga swg 18ga awg 0.036" 0.914mm	22ga swg 20ga awg 0.028" 0.711mm	18ga swg 16ga awg 0.048" 1.219mm	20ga swg 18ga awg 0.036" 0.914mm	16ga swg 14ga awg 0.064" 1.626mm	18ga swg 16ga awg 0.048" 1.219mm	Measure along thinnest axis. Punched rings should be comparable thickness.
Sheet Metal	18ga 0.040" 1.024mm	20ga 0.036" 0.911mm	16ga 0.051" 1.291mm	18ga 0.048" 1.214mm	14ga 0.064" 1.628mm	16ga 0.060 1.518mm
Scales	20ga 0.032" 0.812mm	22ga 0.030" 0.759mm	18ga 0.040" 1.024mm	20ga 0.036" 0.911mm	16ga 0.051" 1.291mm	18ga 0.048" 1.214mm